Tennessee Air Brakes practice test
25 questions · 80% to pass · Required to operate any vehicle with air brakes.
How to use this practice test
Read each question, click an answer, and the correct choice is highlighted with a short explanation referencing the underlying CDL Manual concept. Your live score appears at the top of the page. Refresh to reset.
This test runs entirely in your browser. Nothing is uploaded; no account is required. Pages refresh to a new randomized cut from the bank.
-
1. When the air compressor governor reaches the cut-out pressure, it:
Explanation. The governor stops compression at cut-out, usually around 125 psi, and resumes at cut-in.
-
2. Air brake systems combine three braking systems:
Explanation. Service brakes for normal stops, parking brakes for parking, and emergency brakes that use parts of both.
-
3. The supply pressure gauge shows:
Explanation. The supply gauge displays reservoir pressure available for braking.
-
4. Per federal regulations, air brake systems combine three braking systems:
Explanation. Service brakes for normal stops, parking brakes for parking, and emergency brakes that use parts of both. (Reinforcement variant — same underlying CDL Manual concept.)
-
5. Most state DMV CDL handbooks state that modulating control valves let the driver:
Explanation. Modulating valves provide proportional braking, more pressure with more pedal force. (Reinforcement variant — same underlying CDL Manual concept.)
-
6. The low-pressure warning device must activate before pressure drops below:
Explanation. The warning must come on before air drops below 60 psi.
-
7. In real-world commercial driving, on a tractor-trailer with ABS, the trailer ABS warning lamp is mounted on the:
Explanation. A yellow lamp on the left side of the trailer indicates trailer ABS status. (Reinforcement variant — same underlying CDL Manual concept.)
-
8. Experienced commercial drivers know that a leaking air system should be tagged out of service if pressure loss exceeds:
Explanation. For a parked single vehicle, more than 2 psi/min loss is too much; for a combination, 3 psi/min. (Reinforcement variant — same underlying CDL Manual concept.)
-
9. Experienced commercial drivers know that modulating control valves let the driver:
Explanation. Modulating valves provide proportional braking, more pressure with more pedal force. (Reinforcement variant — same underlying CDL Manual concept.)
-
10. Experienced commercial drivers know that hydraulic brake systems use:
Explanation. Hydraulic brakes use brake fluid; CDL air-brake exam still requires you to know the difference. (Reinforcement variant — same underlying CDL Manual concept.)
-
11. When operating a CMV in interstate commerce, spring brakes (parking/emergency) come on automatically when air pressure drops between:
Explanation. Spring brakes apply at approximately 20-45 psi as air pressure falls. (Reinforcement variant — same underlying CDL Manual concept.)
-
12. When operating a CMV in interstate commerce, antilock braking systems (ABS) help the driver by:
Explanation. ABS preserves steering control by preventing lockup; it does not necessarily shorten stopping distance. (Reinforcement variant — same underlying CDL Manual concept.)
-
13. In real-world commercial driving, air brake reservoirs should be drained:
Explanation. Air tanks must be drained daily to remove water and oil that accumulate from compression. (Reinforcement variant — same underlying CDL Manual concept.)
-
14. When taking the CDL knowledge exam, pumping the brake pedal in an air-braked vehicle:
Explanation. Pumping releases stored air; never pump air brakes during normal stops. (Reinforcement variant — same underlying CDL Manual concept.)
-
15. Experienced commercial drivers know that if the application pressure rises significantly during steady braking, it may mean:
Explanation. A pressure rise during steady application indicates the brakes are not responding properly. (Reinforcement variant — same underlying CDL Manual concept.)
-
16. During a pre-trip inspection, the low-pressure warning device must activate before pressure drops below:
Explanation. The warning must come on before air drops below 60 psi. (Reinforcement variant — same underlying CDL Manual concept.)
-
17. On a tractor-trailer with ABS, the trailer ABS warning lamp is mounted on the:
Explanation. A yellow lamp on the left side of the trailer indicates trailer ABS status.
-
18. Most state DMV CDL handbooks state that a leaking air system should be tagged out of service if pressure loss exceeds:
Explanation. For a parked single vehicle, more than 2 psi/min loss is too much; for a combination, 3 psi/min. (Reinforcement variant — same underlying CDL Manual concept.)
-
19. Per federal regulations, air brake reservoirs should be drained:
Explanation. Air tanks must be drained daily to remove water and oil that accumulate from compression. (Reinforcement variant — same underlying CDL Manual concept.)
-
20. The most common type of foundation brake on heavy vehicles is the:
Explanation. S-cam drum brakes are the most widely used heavy-vehicle foundation brake.
-
21. Per federal regulations, you should drain the wet tank:
Explanation. The supply (wet) tank collects most water and should be drained, with all other tanks, daily. (Reinforcement variant — same underlying CDL Manual concept.)
-
22. Bleeding tanks of air during inspection lets you check for:
Explanation. Pressure drop tests check the integrity of the air system.
-
23. When taking the CDL knowledge exam, when the ABS warning lamp comes on while driving, you should:
Explanation. Service brakes still operate; have ABS serviced as soon as possible. (Reinforcement variant — same underlying CDL Manual concept.)
-
24. Total stopping distance for an air-braked vehicle includes:
Explanation. Air-braked vehicles add brake lag distance because of the time air takes to apply.
-
25. When the ABS warning lamp comes on while driving, you should:
Explanation. Service brakes still operate; have ABS serviced as soon as possible.
About the Air Brakes exam
The Air Brakes endorsement covers the operation of compressed-air braking systems used on most heavy commercial vehicles. Topics include compressor and governor operation, supply and service tanks, brake chambers, slack adjusters, dual air systems, parking brakes, low-pressure warning devices, and the seven-step pre-trip air brake test.
This Tennessee-specific edition uses the same federal source material every U.S. state adopts. The Tennessee DOSHS administers the actual exam at its service centers. Bring your CDL handbook for any last-minute reference; it’s free at every Tennessee DOSHS office.
Once you’re consistently scoring above 90% on this practice set, you’re well above the 80% required to pass the official Tennessee exam. Drill the questions you miss most often, then take the test cold once a day for a week leading up to your appointment.
Tips that actually work
- Read every answer choice before clicking. CDL questions are famous for "best answer" wording where two choices look right.
- Don’t memorize question text — learn the underlying rule. The DMV reshuffles wording constantly.
- Keep a list of the questions you miss. Re-drill them in isolation until you can’t miss them.
- Practice in short, frequent sessions. Two 20-minute sessions per day beats one two-hour cram.
What happens after I pass?
Passing the knowledge test earns you a Commercial Learner’s Permit (CLP). You must hold the CLP for at least 14 days before you can take the road skills test, and you must drive with a CDL-holding instructor in the cab during that period. Once you pass the road skills test, your CDL is issued.